Super Commando Captain

Model MW-39722, Photo by Unknown
Description: Super Commando Captain
Prefix: MW
Detachment: Bounty Hunters Guild
Context: Star Wars The Clone Wars

The Mandalorian Super Commando Captain is a Death Watch soldier, who after the death of Pre Visla, remained loyal to Darth Maul's Shadow Collective while the Night Owls remained loyal to Visla's Lieutenant Bo Katan. This soldier is uniquely identified by the Zabrak style horns mounted to the helmet.

This is a visual guide used for 501st costume approval, not a how-to for construction. Construction details are found at the costume's Detachment website. Measurements provided here are are generalized, and not criteria for approval. All 501st costumes are proportionate to the wearer in terms of size, fit, and scale. During evaluation, both text and images (CRL and Reference) must be considered. When in doubt about a feature of a submitted costume, GMLs should post questions in the Legion forum's DL/GML peer review section.

Required Costume Components

The following costume components are present and appear as described below. For 501st membership only the requirements in black need to be met. This Detachment defines additional, optional costuming details listed in blue and red. Please visit the Detachment website for more details on these options.

• Helmet must be the "Deathwatch" version of the Mandalorian helmet featuring the elongated mandibles and narrow T-visor.
• Dome must be painted red with black "tattoo" pattern painted to match visual references.
• Mandibles and brow must be painted red.
• Earcaps are symmetrical and must be painted red.
• Cheekbones must be painted charcoal black.
• Cheeks must be painted white/light grey (heavily weathered).
• Back panels must be painted black with center slotted section red.
• Helmet dome must feature 10 metal or metal-like polygonal spikes.
• Four (4) small spikes on the crown of the head.
• Four (4) large spikes between the small spikes and the brow line. Spikes also have a triangular base with 2 rivets or the appearance of rivets.
• Two (2) medium spikes on the side of the helmet between the large spikes and the brow.
• Horns are painted silver to give a metallic feel.
• Helmet has a black visor, with the wearer's face not easily visible.
• All paint is weathered to match visual references.

• Must be a cotton or cotton blend, one or two-piece garment colored tan, and must be properly fitted and shaped to the wearer.
• Flightsuit has traditional Mandalorian style double sleeves (long sleeves with short sleeves on top). Short sleeves are approximately 80% the length from the shoulder to the elbow of the wearer.
• Must not have any visible pockets, pouches or zippers once armor is attached.
• There are two options regarding the pant bottoms:
• Option 1: Legs must be long enough to tuck into the top of the boots.
• Option 2: Leg length if left untucked must not extend below the ankle of the wearer.
• Flight suit must be weathered to match visual references.

• Must be made of black leather, leather-like, or similarly sturdy material such as duck cloth or canvas.
• Must have two long shoulder tabs to mount the shoulder armor.
• Vest must be short enough to stop before hitting the girth belt. (Approximately 1-2� long below bottom edge of Ab Armor.)
• Vest is not tucked into the girth belt and allows some flight suit to show.
• Should be weathered to match visual references.

• Must be Animated Death Watch style armor.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must have 4 points with an inward curve connecting the top and bottom point on each outside edge.
• Must be painted red with black stylized "tattoo" pattern painted and weathered to match references.
• Each shoulder must feature 3 polygonal metal or metal-like spikes mounted in the middle in a vertical line. Spikes get progressively smaller from the top to the bottom.
• Horns are centered left-to right on the armor piece and coloring should match the horns on the helmet.
• Armor is connected securely to Flak Vest shoulder tabs.
• Shoulder armor flares out off the shoulders to present a wider than normal silhouette.

• Must be Animated Deathwatch style armor.
• May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must be painted grey/black and weathered to match visual references.
• Must be worn with indented "closure" on the inside of the arm.
• Must have two raised platforms on the top of the gauntlet with the platform closest to the wrist being taller than the one closer to the elbow.
• Left gauntlet must feature a "comms device" constructed to match references.
• Gauntlets will taper to wrist.

• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Symmetrical, angled tombstone shaped hand plates.
• Hand armor must be mounted to the back of each hand and attach without visual straps.
• Plates must be painted grey/black and weathered to match visual references.

• Must be black cotton, canvas or non-piling material. No Leather.
• May use Nomex pilot gloves.
• No visible logos or designs may be present once hand plates are attached.

• Must be Animated Death Watch style armor.
• Consists of collar armor, right and left chest plates, ab plate, and center diamond.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must be painted red with stylized black "tattoo" patterns painted and weathered to match reference images.
• Black tattoo pattern, matching visual references, is painted on the collar, left and right breast plates.
• Chest armor should line up with collar armor at the outer edges.
• Left chest plate has two slotted rectangular indentions.
• Ab plate sides should line up with the bottom outer edges of chest plates.
• The center diamond plate (between breast plates), has a raised vertical rectangle as shown in the visual reference.
• All pieces should attach securely to the vest with proper spacing.

• Must be Animated Death Watch style armor.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must be painted red at the top and fade to grey towards the bottom.
• Fade should begin approximately halfway from top.
• Must have curved cutout at the bottom.
• Interior curved area should match black on armor.
• Should curve in towards wearer on all edges to give appearance of thickness, and sit flush against wearers back.
• NOTE: Collar and backplate DO NOT overlap.

• Must be a Death Watch "arena" style jetpack with snub nose center missile and nozzles mounted directly under the tanks on each side.
• Must be dark grey and grey/black panels and patterns.
• Tank toppers must have a red and white stripe under the cone portion. Red stripe must be under the white stripe.
• Additional red detailing is present on either side of center tank to match visual references.
• Nozzles must be charcoal grey/black.
• Jetpack attaches snugly against the back armor in the proper centered position.
• Paint scheme weathered to match visual references.

• Must be charcoal grey/black leather/leather-like material.
• Belt is approximately 5-6� wide and should be proportionate to wearer, to accommodate proper spacing and appearance with other armor elements.
• Must extend beyond the ammo belt on the top and bottom.

• Must have the following construction elements:
• Rectangular buckle in the center.
• One (1) skinny rectangular section on each side of the buckle.
• Two (2) rectangular sections come next on each side.
• Two (2) large square sections come next on each side.
• On each hip there is a large square section with a smaller square cutout in the center.
• The back of the belt is a mirror of the front.
• Must be charcoal grey/black solid material (plastic, rubber, cured leather, metal, etc.), weathered to match visual references.
• Ammo belt must attach to Girth Belt, centered from top to bottom.
• Should be a height to allow Girth Belt to show above and below by approximately 1-inch.

• Must be Animated Deathwatch style armor.
• Triangular cod piece which must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Bottom must curve inward toward the inseam of the wearer.
• Must be tucked under the girth belt.
• Must be painted red to match the helmet and armor.
• Must weathering must match visual references.

• Must be Animated Deathwatch style armor.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must be painted charcoal grey/black and weathered to match references.
• Armor wraps around the outer thigh with no visible straps/attachment.
• Must feature a solid box holster on each leg.
• Rear upper section of holster box is shorter than front to accommodate Westar pistols.

• Must be Animated Deathwatch style armor.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must be painted charcoal grey/black and weathered to match references.
• Armor attaches to the front of the knees, directly to flight suit with no straps or visible means of attachment.

• Must be Animated Deathwatch style armor.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Must be painted red and weathered to match references.
• Must fit closely around the shin.
• Must be made of three angled sections: flat front and angled flat sides that curve at back slightly to fit wearers leg. The tops of the side segments must be angled downwards.
• Armor attaches directly to flight suit with no straps or visible means of attachment.

• Must be Animated Deathwatch style armor.
• Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
• Armor consists of Ankle Spat, Toe Cap and Heel Cover with rectangular raised detail that wraps around back of heel.
• Ankle spat covers the top of the foot, hiding laces if present.
• Must be painted charcoal grey/black and weathered to match references.
• Boot armor connects with no visible means of attachment.

• Must be charcoal grey/black canvas with black rubber sole.
• Sole must have rugged tread.
• Boot must be angle-height.
• Palladium boots Pampa Hi, in canvas, are an example of an acceptable style.

Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.

• Must be Animated Deathwatch style Westar Pistols.
• Must be painted silver with charcoal grey/black grips, properly weathered to match visual references.