Commander Wolffe (Phase I) — Realistic

Model CC-21500, Photo by Javier D Luc
Description: Commander Wolffe (EU)(Phase 1)
Prefix: CC
Detachment: Clone Trooper Detachment
Context: Sideshow toys realistic design of Commander Wolffe.

Commander Wolffe CC-3636 is the leader of the 104th Battalion’s Wolfpack Squad. Shown here is his Phase I armor designed by and produced by Sideshow. Talented in military strategy and leadership skills, Wolffe favors service on the front lines over more tedious assignments, such as supply missions or support duties.

This is a visual guide used for 501st costume approval, not a how-to for construction. Construction details are found at the costume's Detachment website. Measurements provided here are generalized, and not criteria for approval. All 501st costumes are proportionate to the wearer in terms of size, fit, and scale. During evaluation, both text and images (CRL and Reference) must be considered. When in doubt about a feature of a submitted costume, GMLs should post questions in the Legion forum's DL/GML peer review section.

Required Costume Components

The following costume components are present and appear as described below. For 501st membership only the requirements in black need to be met. This Detachment defines additional, optional costuming details listed in blue and red. Please visit the Detachment website for more details on these options.

• Realistic style Phase 1 style helmet.
• Helmet fin on top of dome with red “brake light” at the rear point.
• Rear fin has "brake light" cover installed.
• Black or dark smoke eye lens that obscures the wearer’s eyes.
• Helmet frown is painted black.
• Six rounded “teeth” are cut from the frown
• Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
• Six black vents on each side of helmet cheeks under the ear.
• Center chin vocoder is painted black.
• Back of helmet has a recessed vent detail with three vertical rib details.
• The helmet has white wolf markings covering the dome, sides, back and chin of the helmet that matching references
• The grey areas are weathered with chips and scuffs revealing the underlying white
• Four weathered, yellow “Kill stripes” are present in the white space of the dome on each front quarter.
• Red Inverted triangle is present, centered on the dome between the kill stripes.
• A white range finder and stalk are present on the right ear and are weathered with black scuffs.
• The stalk is mounted to the ear via a semicircle cap.
• The left ear has a semicircle cap matching that of the right ear.
• Helmet is weathered with black scuff and rust brown washes.

• Neck seal is black in color with vertical ribbing or smooth in appearance.
• No logos or labels are visible.
• If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.

• Realistic style ROTS phase II clone undersuit.
• Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.

• Realistic style shoulder armor.
• The left shoulder is painted grey with Plo Koon's sunburst in white.
• The left shoulder has a mounted antenna.
• The right shoulder is painted grey with a white wolf pack emblem matching visual references.
• Shoulder shapes are a mirror image of each other.
• The Shoulder armor slightly curves back at the bottom of the shoulder.
• Armor is weathered with black scuffs and shades of grey.

• Realistic style upper arm armor.
• Armor is painted matte or satin white, with Grey details.
• Each arm has a vertical center grey detail stripe approx. 2.5–3" (5–7.5cm) wide that ends with (4) “teeth” approx. 1" (2.5cm) from the bottom of the bicep.
• Armor has a front hard line outside edge and inside is rounded.
• Armor piece has a dimple on the lower area of the back of arm.
• Armor is seamless.
• No visible traces of how the armor was assembled are shown.
• Grey areas are weathered with scuff marks, chips and fading.
• Scuff marks and chips expose the underlying white paint.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Realistic style elbow armor.
• Armor is painted matte or satin white.
• Elbow straps are white and have a raised detail line at the top and bottom of the strap.
• Armor has two parallel dashed detail slots on each outside edge of elbow at the strap connection.
• Elbows are mirror images of each other with a notched area on the outside of the elbow above the detail marks.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Realistic style Forearm Armor.
• Armor is painted matte or satin white with grey detail.
• Grey Wolf’s teeth styled markings are present matching references.
• Right forearm has a compad with eight (8) small buttons, one (1) large main button, and one (1) smaller rectangular button closest to the elbow.
• The compad is blue and aligns with the right forearm blue stripe.
• Armor is seamless.
• No visible traces of the how the armor was assembled are shown.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Realistic style hand plates.
• Armor is painted matte or satin grey.
• Hand plates are mirror images of each other.
• Hand plates have a top curving ridge that comes to a point over the index or middle finger just past the main knuckle of the hand.
• Armor is weathered with various scuffs marks, chips and fading.
• Scuffs or chips on the blue expose the underlying white.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
• Gloves cover any exposed skin.
• Gloves do not show any labels or logos when the armor is worn.

• Realistic style Chest Armor.
• Armor is painted matte or satin white.
• The upper chest is painted with a grey arched section matching visual references.
• Two detail slots on lower outside edge of right raised chest area.
• Chest and back plate match together at the sides and shoulders with no open gap.
• Butted seam lines are present.
• Shoulder straps are slotted into the detail ridges of the chest to shoulder connector area.
• Shoulder straps are grey.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Realistic style Back Armor.
• Armor is painted matte or satin white.
• Top half of the armor and detail plate is painted grey matching visual references.
• Back has a detail plate with four circles on top, two elongated areas on left, and vents on lower right.
• Back and chest armor match together at the sides with no open gap.
• A seam line is present.
• Shoulder straps are slotted into the detail ridges of the top connection points.
• Shoulder straps are grey.
• Armor is weathered with various shades of grey.

• Realistic style Abdomen Armor.
• Armor is painted matte or satin white.
• Eight (8) ¼" diameter holes are visible when worn, with four (4) holes inside each indented channel of the abdomen.
• Abdomen section wraps around the wearer’s body and is sealed at sides or at back.
• Abdomen is completely contained under the chest and back armor.
• Armor aligns with codpiece with the seam line hidden by the belt.
• Armor has black scuff marks.
• Armor is weathered with various shades of gray.

• Realistic style Codpiece and Posterior Armor.
• Armor is painted matte or satin white.
• Codpiece and posterior armor connect at the hips.
• Armor is weathered with various shades of gray.
• Armor has black scuff marks.

• Realistic style clone belt, beltboxes, and detonator.
• Belt, boxes, and detonator are painted matte or satin white.
• Belt front between front boxes has three (3) vertical rectangle indents which are spaced apart by two protruding rectangle areas.
• The rest of the belt is flat surfaced with raised edging on the top and bottom that run along the rest of the belt.
• Eight (8) Belt boxes are attached to the belt with four (4) on each side.
• The two largest boxes are in front with angled top surface that is higher toward the center.
• The smallest boxes are located behind the front boxes, about ⅛" apart and have an angled end on top.
• The medium sized matching boxes, with flat top cover are about ⅛" from smallest boxes.
• Left rear box is spaced closer to detonator and has two square buttons in the top left corner, and two (2) dashed indented detail marks on bottom right.
• Right rear box is spaced closer to detonator and has a bar with two (2) small cylinders centered and two (2) dashed indented detail marks on the bottom left.
• A detonator is centered and attached to the back of the belt.
• Detonator tube is about 2.25" diameter with wider detailed end caps.
• Seven (7) horizontally aligned square buttons are on left side of tube when viewing from behind.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Realistic style Holsters.
• Animated style holsters are not permitted.
• Holsters are painted matte or satin white.
• Holsters are hung from the belt via grey or black web straps on each hip aligned under the second smallest belt box on each side.
• No visible attachment at the belt.
• Web straps run the length of the holster on the side closest to the kama.
• Inverted triangle detail is present on front facing edge near top of holster.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Animated style Kama.
• Kama is made of matte vinyl or leather like material with canvas or cloth backing.
• Kama is black with grey trim.
• Trim is fabric with visible texture.
• Trim grey is slightly darker than the armor.
• Bottom corners of the kama are rounded.
• Front edges of the kama line up with the inside edges of the front boxes.
• Panels of the kama are approx. 4" apart at the back and connect under the belt.

• Realistic style Thigh Armor.
• Armor is painted matte or satin white.
• Thigh Armor has a flat triangle area above the knee which transitions to a ridge line that runs up the front of the thigh to the top edge.
• Rear of armor has an indented area.
• Armor is seamless.
• No visible traces of how the armor was assembled are shown.
• Armor is weathered with shades of gray and/or brown.

• Realistic style knee armor.
• Armor is painted matte or satin white with grey detail.
• A grey, upward pointing triangle extends from the bottom of the knee with its point at the top edge.
• Knees have a protruding flat area in front oriented towards the top of Knee.
• Knees bend around the front and connect to white detail clips that connect the strap on each side.
• A white colored flat strap, about 2 inches wide, wraps around back of leg.
• Flat Strap has raised ⅝" wide gray center strap.
• Grey areas are weathered with scuffs and chips that expose the underlying white paint.
• Armor is weathered with shades of grey.

• Realistic style Lower Leg Armor.
• Armor is painted matte or satin white.
• Lower legs are mirror images of each other.
• Front of lower leg has a flat triangular detail at the top which transitions to a ridge line that travels down the front of the armor to the ankle.
• Back of lower leg armor features arched indentation, just under the calf, that follows down to the ankle.
• Bottom of this indentation features a smaller arch detail at the heel.
• Outside of the calf is closed.
• Calf can have an access area on the inside of the leg.
• Calves are seamless and have a trap door access through the indent in the rear of the lower leg.
• The lower portion of the shins are painted grey with the top edge of the grey ending in a wolf’s teeth edge matching visual references.
• Armor has black scuff marks.
• Armor is weathered with shades of grey.

• Realistic style boots
• Animated style boots are not permitted.
• Boots are grey matching armor.
• Boots are ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle.
• Boots are lace-less
• Boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two (2) protruding discs at each side of the strap.
• There are no markings or labels from the shoe maker.
• Boot’s soles are flat.
• Boot’s soles are colored primer grey.

Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.

• The number of pistols carried is dependent on the amount of holsters.
• This is the realistic variant of the DC-17 blaster.

• Realistic Clone Style DC-15S Blaster.
• Blaster may be scratch built out of plastic, wood, metal or cast in resin.
• Blaster has realistic Episode II or Episode III details:
• Wire frame sight.
• Folding stock.
• Twelve radiator fins evenly spaced along the length of barrel.
• Igniter detail knobs.
• Charge magazine clip on right side.
• Total length is approximately 26 inches (66 cm).
• Because of the scale, the Hasbro version is incorrect.

• Realistic Clone Style DC-15A Blaster Rifle.
• Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
• Blaster has realistic Episode II or Episode III details:
• Flip up sight in down position.
• Ten radiator fins are evenly spaced along the length of the barrel.
• Power setting adjuster detail lever.
• Sniper Scope attached under rifle in storage position.
• Charge magazine clip on left side.
• Igniter detail knobs.
• Total length is approximately 55 inches (139.7 cm).
• Because of the scale, the Hasbro version is not allowed.