Republic/Imperial Fleet Officer

ID_Fleet_Officer_Fandb

Visit the Gallery for this Costume for more models and parts views.

Model ID-99933, Photo by Cedric Grafas
Description: Republic-Imperial Fleet Officer
Prefix: ID
Detachment: Imperial Officer Corps
Context: Star Wars Episode III Revenge of the Sith

These officers served the Republic Starfleet from its formation to its transition into the Empire's forces.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.

This is a visual guide used for 501st costume approval, not a how-to for construction. Construction details are found at the costume's Detachment website. Measurements provided here are generalized, and not criteria for approval. All 501st costumes are proportionate to the wearer in terms of size, fit, and scale. During evaluation, both text and images (CRL and Reference) must be considered. When in doubt about a feature of a submitted costume, GMLs should post questions in the Legion forum's DL/GML peer review section.

Required Costume Components

The following costume components are present and appear as described below. For 501st membership only the requirements in black need to be met. This Detachment defines additional, optional costuming details listed in blue and red. Please visit the Detachment website for more details on these options.

ID_Fleet_Officer_hat

Republic/Imperial Hat

  • Olive/Grey fabric is a medium weight suiting material matching the pants and tunic.
  • Gabardine style weave is most accurate.
  • The dome of the hat has 2 side seams that run parallel with each other from the top of the peak to the back of the hat, another seam is dead center of the dome from above the code disk to the back of the hat.
  • There are hemisphere shaped flaps on each side of the dome.
  • Code disk is positioned in the center of the front of the dome.

OPTIONAL Level two certification (if applicable):

  • Front bill extends 3" down.
  • Side flaps have a piping detail.

OPTIONAL Level three certification (if applicable):

  • Code disk exactly matches screen-used prop.

ID_Fleet_Officer_tunic

Tunic

  • Olive/grey colored fabric is a medium weight suiting material exactly matching the pants.
  • Tunic is double-breasted with a left over right closure on the tapered yoke.
  • Yoke comes up across the shoulder to the top shoulder seam.
  • The standing collar has square corners and closes snugly.
  • Collar edges close on the right side of the neck with eye hooks
  • The tunic has a seam at chest height on the front center panel curving at each end.
  • There are epaulets on each shoulder.
  • Sleeves are long, and without cuffs or buttons.
  • There are one or two un decorated bands on the lower section of both sleeves.
  • Tunic is constructed with no top-stitching (stitches visible on the exterior surface of fabric).

OPTIONAL Level two certification (if applicable):

  • Collar is approximately 1.25' to 2.5' tall
  • The back of the tunic has two seams that run vertical with a slight curve at the top meeting the front seams.

OPTIONAL Level three certification (if applicable):

  • Collar has a detail matching the closure on the left side but is non functional.

ID_Fleet_Officer_pants

Jodhpurs

  • Olive/grey fabric is a medium weight suiting material exactly matching the tunic.
  • Trousers are riding breeches with semi-stiff flares to the hip/thigh area and tucked into the boots.
  • Pockets are acceptable but shall not be visible with the tunic on.

ID_Fleet_Officer_Rank

Rank Bar

  • Worn on the left side of the tunic above the piping.
  • Rank consists of colored plastic tiles mounted inside a frame-plate.
  • If double the upper an lower frame are divided by a small indentation.
  • Three blue tiles in the top frame.
  • Two red tiles in the bottom frame.
  • Single bars consist or 3 red or 3 or 4 blue tiles.

OPTIONAL Level two certification (if applicable):

  • Each bar is approximately 1 1/8" (28.6 mm) height.
  • Length of the upper frame-plate is approximately 2 1/3” (6cm) wide, if double bars are used.
  • Length of the lower frame-plate is approximately 1 5/8” (4,1cm) wide. if double bars are used.
  • Rank tile dimensions are approximately 5/8" (16 mm) width x 7/8" (22 mm) height.
  • The mounted tiles are slightly horizontally curved upwards in the middle.

ID_Fleet_Officer_belt

Belt

  • The belt is constructed from a non-textured leather or a leather-like material.
  • Approximately 2" (50.8 mm) in width, up to 3" (76.2 mm) is acceptable.
  • There is one loop on the belt each side of the buckle.
  • The buckle is constructed from a horizontally brushed metal, or metal looking material.
  • Buckle is adorned with a Code Disk at the center.
  • Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.
  • Buckle is rectangular and slightly taller than the belt.

OPTIONAL Level two certification (if applicable):

  • The buckle size is approximately 2 5/8" (66.7 mm) high and 4 1/8" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners.
  • Belt is made of leather.
  • Buckle has a slight horizontal curve.
  • Belt code disk has a notch.

ID_Fleet_Officer_boots

Boots

  • Boots do not have a zipper.
  • Boots are bulged wider on both sides of the ankle.
  • The upper edge of the shaft is cuffed.

OPTIONAL Level two certification (if applicable):

  • Boots are made of leather.

OPTIONAL Level three certification (if applicable):

  • Cuffs are maroon in color.

ID_Fleet_Officer_gloves

Gloves

  • Gloves are made from black leather or leather-like material and have no top stitching or decoration
  • Gloves cover wrist.