Republic Medic

Model ID-90179, Photo by ID-15577
Description: Republic Medic
Prefix: ID
Detachment: Imperial Officer Corps
Context: Star Wars: The Clone Wars

These medics serve in the cloning facilities of Kamino and provide support for cloning unit malfunctions, and injuries of the clones during training.

This is a visual guide used for 501st costume approval, not a how-to for construction. Construction details are found at the costume's Detachment website. Measurements provided here are generalized, and not criteria for approval. All 501st costumes are proportionate to the wearer in terms of size, fit, and scale. During evaluation, both text and images (CRL and Reference) must be considered. When in doubt about a feature of a submitted costume, GMLs should post questions in the Legion forum's DL/GML peer review section.

Required Costume Components

The following costume components are present and appear as described below. For 501st membership only the requirements in black need to be met. This Detachment defines additional, optional costuming details listed in blue and red. Please visit the Detachment website for more details on these options.

• Costumer is clean shaven

• Cloth is a medium-weight suiting material that matches the tunic and trousers perfectly.
• Gabardine weave is the most accurate.
• The base of the hat is tapered, with a crown approximately 4 inches (101.6mm) high.
• Front and rear "flaps" overlap at the sides and are approximately 4 inches (101.6mm) high.
• The front beak extends down 3 inches (76.2mm) and is decorated with five (5), six (6) or seven (7) concentric stitches.
• Imperial Code Disk in the centre of the front vertical flap.
• At the bottom of the front flap there is a red stripe 0.59 inches (1.5cm) wide, the same red as the stripes on the sleeves.

• White fabric is a mid-weight suit fabric that matches the pants perfectly.
• The tunic is double breasted with a left-over-right closure at the tapered yoke.
• The yoke extends over the shoulder to the upper shoulder seam.
• The stand-up collar has square corners with a left-over-right center closure.
• The collar contains a modesty panel.
• The tunic has medium gray matt satin piping.
• On each shoulder are rectangular epaulettes in the same gray as the piping.
• The epaulettes have the dimensions 4.92 inches (12.5cm) by 2.75 inches (7cm).
• The sleeves are long and without cuffs or buttons.
• Sleeves contain one (1) seam, on the inside.
• On both sleeves there are two rank bands made of gray faux leather in the same gray as epaulettes and piping.
• The tunic is constructed without topstitching (seams are visible on the outer surface of the fabric).
• The back of the tunic has a seam that runs down the center of the tunic from the neck to the hem.
• There is a slit on the back of the tunic that runs from belt level to the lower edge.
• On the outside of the sleeves, two parallel red stripes, as wide as the rank stripes, run the length of the sleeve from the epaulette to the cuff. The total width of the two stripes end with the width of the epaulette.
• On the right chest is the Kamino Doctors patch.
• Additional tunic detail can be found here.

• White fabric is a medium weight suiting fabric that matches the tunic perfectly.
• The trouser legs are straight, without rider flaps, and are worn tucked into the boots.
• Pockets are acceptable but must not be visible when the tunic is on.

• The rank bar is worn on the left side of the tunic over the piping.
• Rank consists of colored plastic tiles mounted in a frame panel.
• The rank bar consists of three tiles in a row, one blue tile on the right and two red tiles on the left.

• The belt is made from a non-textured brown leather or leather-like material and is approximately 2 inches (50mm) wide.
• There are no loops on the belt.
• The buckle has rounded corners and is made of a horizontally brushed metal or metal-like material.
• The buckle is embellished with a Republic code disc in the center.
• The code disc is a stepped cone shape with the appearance of two (2) discs stacked on top of each other.
• The larger disc is 1.4 inches (3.5cm) and the smaller disc is 1 inch (2.5cm) in diameter.

• The boots are made of brown leather or leather-like material.
• If stretch inserts or zippers are present, they must be hidden on the inner shaft.
• Boots have a wider arch on either side of the ankle.
• The upper edge of the shaft is shaped as a cuff.

Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.

• Gloves are made of brown leather or leather-like material.
• Gloves can be plain or have 3 stitch lines on the back of the hand.

• Realistic clone style DC-15S blaster.
• Blaster can be custom built out of plastic, wood, metal or cast in resin.
• Blaster has realistic Episode II or Episode III details: wire frame sight, collapsible storage.
• Twelve (12) radiator fins evenly spaced along the length of the cylinder.
• Igniter detail buttons.
• Charge magazine clip on the right.
• The overall length is approximately 26 inches (66cm).
• Due to the scaling, the Hasbro version is wrong.